News

News

News Center
Powder coating production equipment should be how to choose?

Powder coating production equipment should be how to choose?

Basic requirements for powder coating production equipment: a The equipment must have advanced technical performance, can meet the process requirements of different formulations of powder coatings, and has stable technical performance, low failure rate and high product recovery efficiency. B has reliable according to the whole. The design, processing and operation of powder coating production equipment must meet the requirements of the national standards for mechanical and electrical compliance and environmental protection.

20

2024

/

06

The technical performance of the ACM-C series milling unit is comprehensively improved

The technical performance of the ACM-C series milling unit is comprehensively improved

ACM-C series milling units are controlled by PLC programming system, which is easy to operate and can realize remote control. PLC electronic weighing system, automatic box feeding and discharge, high production efficiency, low noise milling system noise ≤ 85 decibels, grinding body adopts double air duct, temperature is greatly reduced, ideal and stable particle size distribution can be obtained by adjusting operation system parameters, and has excellent explosion-proof equipment and explosion-proof performance.

20

2024

/

06

Maintenance method of powder equipment

Maintenance method of powder equipment

During the period of using the equipment, each shift should refuel the main shaft of the equipment. Together, it is necessary to grasp that the oil injection time should not be too short or too long. During the oil injection period, the operators should also grasp the amount of oil at a high level, not too much or too little, otherwise it will have a certain impact on the equipment.

20

2024

/

06

Comprehensive Optimization Strategy for Improving Pulverization Rate of Mill

Comprehensive Optimization Strategy for Improving Pulverization Rate of Mill

Improving the powder yield of the mill is a comprehensive problem, involving the optimization of many aspects. First of all, choose the appropriate mill model and specifications to ensure that it matches the characteristics of the raw materials and production needs. Secondly, optimize the pretreatment process of raw materials, such as cleaning, screening and wetting, to reduce impurities and adjust the moisture content, thereby improving the grinding effect. In the process of grinding, reasonably adjust the grinding roller gap, speed and feeding amount to ensure that the material is fully ground and broken in the mill. At the same time, regularly check the wear of the grinding roller and screen, and replace the severely worn parts in time to maintain the good working condition of the mill.

20

2024

/

06

Process Flow and Quality Control of Thermosetting Plastics Extruder

Process Flow and Quality Control of Thermosetting Plastics Extruder

The process of thermosetting plastic extruder is a complex and delicate process, which is mainly used to produce thermosetting plastic products with specific shapes and properties. First of all, raw material preparation is a key step. The pretreated thermoset plastic pellets are fed into the feed throat of the extruder. These particles need to meet certain quality requirements to ensure that the subsequent processing process is carried out smoothly.

20

2024

/

06

The basic principle of pulverizing equipment

The basic principle of pulverizing equipment

1. Material feeding: First, the materials to be processed are fed into the pulverizing equipment through the feeding system. 2. Crushing: Inside the equipment, the material is broken down into smaller particles through the action of a crusher or mill. The purpose of this step is to reduce the particle size of the material in preparation for subsequent processing. 3. Refinement and wear: The crushed material is further refined, such as through the close rolling of the grinding roller and the grinding ring, so that the material particles are further refined. In this process, the material is subjected to friction, impact and other external forces, so as to achieve the refinement effect.

20

2024

/

06

< 1 >

Get a Free Consultancy

Submit MORE
%{tishi_zhanwei}%
Yantai Wanheng

Committed to providing energy-saving, intelligent, clean, safe and efficient high quality powder equipment production line for the powder industry.

2-2, Sanli Road, Muping District, Yantai

Shandong, China

Cellphone: +86 176 1618 8999

WhatsApp:  +86 132 0535 2071,+852 5634 4039

Email:  wh.powder@outlook.com, info@wanhengpowder.com

Copyright© Yantai Wanheng

Powered by: 300.cn